HDCVI – The Low-Cost HD Security Camera

Surveillance cameras usually do not come cheap—especially the highly-sophisticated ones that can provide higher-quality and clearer videos. However, there are low cost alternatives to pricey security cameras and you can consider them for your home or business. The HDCVI is a good option in low cost HD security cameras. The name stands for high definition composite video interface, and it uses technology that transmits video signals in a different method over coaxial cables.

Before HDCVI, analog CCTV was the norm. The problem was its resolution, which was limited only to 960h—meaning, there is a 30 percent increase in the horizontal resolution, resulting in a 960 x 480-pixel maximum resolution. To improve transmission, you would usually have to upgrade to digital video via HDSDI or network IP formats. With HDCVI, you can have a cost-effective network IP solution that relies on a video transmitter and a receiver that can transmit videos in a resolution of up to 1080p or 1920 x 1080 pixels. The videos are uncompressed and can be sent over standard coaxial cables used in conventional CCTV camera systems.

The uncompressed video of HDCVI can be transmitted over longer distances without bandwidth and latency issues, which were common with conventional network IP and HDSDI cameras. HDCVI can transmit control (PTZ or OSD), audio, and video over a coaxial cable, too, so you do not have to worry about having separate cables for every kind of transmission. HDCVI systems cost almost the same as older CCTV analog technology, but they are far more affordable than IP network or HDSDI cameras. Hence, if you have to choose between analog CCTV and HDCVI, consider going for the latter to get higher resolution for your money. Some providers of security surveillance cameras solutions give free software to enable remote moving, and surveillance apps for your tablets and smartphones to go with the HDCVI system.

Blog Source URL: http://www.securitycameradistributor.com/HDCVI-The-Low-Cost-HD-Security-Camera_b_17.html

Connecting A Wireless Security Camera to Wireless Router

It can be troublesome to connect the wireless IP camera to a wireless router, especially if you have not done that before or you simply lack expertise and the experience to do it. After all, not everyone can be completely knowledgeable in networking technologies and terminology. But by following these steps, you should be able to successfully connect a wireless security camera system to a Wireless router on your own:

1. Access the web interface of the IP camera
   
   Some Wireless security cameras system are incapable of PoE, so their default IP address, along with NVRs and other IP cameras is 192.168.1.108, unless noted otherwise by the manufacturer or provider. You may have to change your network configuration to see the web service of the camera or use the IP config tool provided by the security camera provider to change the IP address.
   
   Use an Ethernet cable to connect your camera to your network before plugging the 12v DC adaptor. Wait around a minute to let the camera warm up and power up on its own and let the network access it. Using your browser (i.e. Internet Explorer, Chrome, or Firefox), go to the IP address of the camera.
   
   
2. Configure the address
   
   On the web service, look for the drop-down box with ‘WIRE(DEFAULT)’ and pick ‘wireless’. Click the ‘DEFAULT’ button beside the drop-down box, then click the radio button that says, ‘STATIC’. From there, you can alter the camera’s address, but make sure that it will not cause any problems with another device connected to your network. Likewise, make sure that the default gateway is right and the subnet mask is the same as the rest of the network. Remember that the Wireless address should not be the same as your wired address, so set it differently. Once you are done, remember to save and allow the device to refresh.
   
   
3. Connect to the wireless router
   
   Find Setup, then choose Network, which should lead you to Wireless, and click ENABLE. Click ‘SEARCH SSID’ to find the available networks, or choose ‘ADD SSID’ if your network isn’t broadcasting on an SSID. Double-click your network’s name and input your credentials. Make sure the camera is connected properly by disconnecting the network cables and power from it. Wait 10 seconds before reconnecting the power, and give it two minutes to boot and connect to your newly configured wireless network. From there, try connecting the camera via your web browser using the newly configured wireless IP address.

Blog Source URL: http://www.securitycameradistributor.com/Connecting-A-Wireless-Security-Camera-to-Wireless-Router_b_16.html